Electrical System
Perform every 6 months
- 12 volt
- Hotskin testers
- All lights
- Monitor panel
- 110-Volt system priority
- Converter operation and output
- Shore cord and circuit breakers
- Generator operation and output
45 Point Inspection
Includes comprehensive inspection points in these areas
- Check all electrical outlets
- Check inverters and converters
- Check generator systems
- Check plumbing for leaks and proper operation
- Check LP systems
- Check all appliances
Wheel Bearing Packs
Single Axle *
Double Axle *
Triple Axle *
Bearing Packs Include
- Inspect brake shoes, bearings and magnets
- Clean & repack wheel bearings
- Adjust break linings as needed
- Verify the operation of the electric break magnets &
break-away switch
- Grease seals are extra, prices vary by axle size
*Everyday members-only low price
Water Heater Service
For operation safety and fuel efficiency
- Check condition of Anode Rod
- Check relief valve
- Adjust burners and electrodes
- Check thermocouple
- Check module boards
- Check complete operation
- Check burner assembly, remove nests, bugs, webs, etc.
Oven/Range Service
- Check for proper LP pressure & adjust as needed
- Check for accumulation of dirt, grease, dust or spider webs
- Light each range burner one at a time, check for variable flame
while rotating the valve
- Test oven temperature: adjust as necessary to +/-25 of set point
Rubber Roof Preventative Maintenance
Manufacturers recommend this service annually
- Clean rubber roof with specially designed cleaning agents
- Apply UV-Blocking treatment to protect rubber membrane
We Offer Roof Inspections at Select Camping World Locations:
- Roof Leak Checks
- Rubber Roof Replacement
- Roof Repairs
- Roof Seam Seals
Refrigerator Service
- Verify unit is air tight in compartment
- Refrigerator is properly vented (roof and sidewall)
- Clean and adjust burner and orifice
- Inspect and test all door seals
- Check LP Pressure and proper voltage
- Clean roof vent and check baffle
Water System Check
- Water pump operation
- Check all faucets
- Check holding tanks
- Check fresh water fill
- Complete water line pressure test
- Check all gate valves
Appliance/Accessories Check
Check the following for proper operation
- Antennas
- Furnace
- DVD Players
- Roof - A/C
- Water Heater
- Refrigerator
- Range/Oven
- Awnings
- TV's
- Washer/Dryer
LP Inspection Service
- Inspect regulators and LP tanks
- Complete a drop down pressure test
- Complete a line pressure test
- Check all LP detectors
RV Orientation
Orientates the customer with
- Exterior Components
- Interior Components
- Dashboard Leveling Systems
A/C Service
- Check air temperature drop across the evaporator coil
- Check compressor voltage
- Check compressor amperage
- Remove and clean A/C Filter
- Examine Shroud for cracks and damage
- Clean and unclog A/C roof drains
Basic Winterization
- Drain fresh water tank and water heater
- Blow out water lines with compressed air
- Open toilet valve allow air to force out any water
- Fill P-Traps with anti-freeze
- Includes 1 gallon of anti-freeze
Complete Winterization
- Drain fresh water tank and water heater
- Blow out water lines with compressed air
- Fill P-Traps with anti-freeze
- Includes up to 2 gallons of anti-freeze
- Pump anti-freeze through fresh water lines
with water heater bypass already installed
Deluxe Winterization
- Drain fresh water tank and water heater
- Blow out water lines with compressed air
- Fill P-Traps with anti-freeze
- Pump anti-freeze through fresh water lines
with water heater bypass already installed
- Winterize ice maker and/or water filter
Generator Oil Change
Manufacturers recommend this service every
75 operating hours or 12 months
- Change oil and filter
- Service includes required oil and filterIf needed, Generator
removal & any additional parts will be an extra charge
Gas Generator Service
- Clean & Check Battery & Connections
- Visual Inspection of Exhaust System
- Clean Spark Arrester
- Verify CO Detector & Operation
- Check Air Filter – Replace as Necessary
- Change Oil & Filter
- Check Fuel Filter/Replace as necessary
- Perform Load Test
Furnace Service
For operation safety & fuel efficiency
- Clean main burner orifice
- Clean/Inspect/Adjust electrode assembly
- Clean blower wheel
- Test module board/inspect & clean board contacts
- Clean & inspect combustion chamber
- Inspect fan motor
- Clean & inspect vent tubes and outer casing
- Reassemble furnace using new gaskets
